-
Notifications
You must be signed in to change notification settings - Fork 0
ezmlm split.1
ezmlm-split - distribute (un)subscribe requests to sublists
ezmlm-split dir [ -dD ][ splitfile ]
If the action is -subscribe or -unsubscribe, ezmlm-split analyzes the target of the request, computing a hash in the range 0-52 from the address, and determines the ``domain key'', i.e. the two top levels of the host address in reverse order. Thus, the domain entry for ``d@a.b.c'' becomes ``c.b'' and the one for ``d@a'' becomes ``a''.
The hash and domain parts are then tested against successive lines of splitfile (default is dir*/split***). If a match is found, the request is forwarded to the corresponding sublist, and ezmlm-split exits 99. If splitfile does not exist, a match is not found, or action is not -subscribe or -unsubscribe, ezmlm-split exits 0.
In splitfile, blank lines and lines with ``#'' in position 1 are ignored. Other lines are expected to be of the format ``dom:low:hi:list@host'', where ``dom'' is the top level domain, ``low''-``hi'' the range of the hash (defaults 0 and 52), and ``list@host'' the name of the corresponding list (default is the local list). A line is considered to match if the address hash is between ``low'' and ``hi'' inclusive and ``dom'' is empty, or if the ``domain key'' matches ``dom'' for the full length of ``dom''. Thus, the address ``user@aol.com'' would match ``com'' and ``aol.com'', but not ``host.com''.
If the domain specified is the top level domain up to 3 characters, the split is identical as that used by the SQL subscriber interface. This is recommended. There can be several entries for a given sublist.
ezmlm-split can be used also for list with SQL-based sublisting. In this case, addresses matching the splitfile are forwarded to the respective non-SQL sublist, and non-matching addresses are handed by the SQL sublist.
ezmlm-split uses ezmlm-queue(1) to send messages. ezmlm-split sets environment variables from /etc/indimail/ezmlm/global_vars. This can be used to set queue related variables for ezmlm-queue
If /etc/indimail/control*/qmqpservers*** exists, ezmlm-split will use qmail-qmqpc(1) to send messages. Server IP addresses listed one per line in /etc/indimail/control*/qmqpservers*** will be tried in order.
-d
(Default.) Do. Forward requests to the appropriate list.
-D
Do not process messages. Rather, read addresses, one per line from
stdin, and print ``sublist@host: address'' where ``sublist@host'' is
the address to which the request would have been forwarded in normal
operation. This is used to process a set of existing addresses into a
set of address collections, one per sublist. The output can be sorted
and easily processed into a set of files, one per sublist containing the
addresses that sublist handles.
To use a hierarchy of sublists, set up the master list and add a ezmlm-split line before the ezmlm-manage(1) line in dir*/manager***. Create any number of sublists of the main list on other local or distant hosts. Ideally, these should be non-archived, to point to the correct message numbers of the main list archive (see ezmlm-send(1). You can use ezmlm-make -Cezmlmsubrc for this. If you don't, use the text files from the main list, except bounce-bottom. Next, create split in the main list directory to achieve an appropriate split. Load splitting between several local hosts is best achieved by hash, with a blank domain. Geographical splitting with hosts in different countries is best done via ``domain'' and naturally, a large domain can be subdivided by hash.
Subscribers will receive all messages 'From:' the main list. When they subscribe or unsubscribe, the request will be forwarded to the appropriate sublist, which will handle the confirmation. All information, except bounce-bottom refers the user to the main list. Thus, to the user the list appears as a single list with the address of the main list, and distribution among sublists is at the discretion of the administrator of the main list.
In general, the main list should be disabled, while changing the sublist split. This can be done by changing the mode of dir*/lock*** to 0 or by setting the sticky bit for the home directory of the user controlling the list.
To remove a sublist, edit the lines for that sublist in the splitfile to point to another list, and add the existing subscribers of the removed sublist to the sublist taking the load. When splitting a sublist into several sublists, create the new sublists, and edit the split file to distribute the load between them (usually by hash). Process the subscribers of the old list with:
| ezmlm-split -D dir | sort | program
where to get one file of addresses per new sublist, ``program'' could be:
#!/usr/bin/perl
while (<>) {
($f,$t) = split (':');
$t =~ s/^ //;
if ($f ne $of) {
$of = $f;
close(OUT) if ($of);
open(OUT,">$f") or die("Unable to open $f");
}
print OUT $t;
}
close(OUT) if ($of);
Remove all subscribers from the old list, and add the respective subscribers to each list.
For any more drastic reorganizations, collect all the subscribes of the affected sublists, create the new subscriber lists, and update the subscribers of the affected lists.
Reorganizations are easier done when lists use SQL support. By temporarily using SQL support, reorganizations can be done on running lists even when normally using ezmlm-split and local subscriber databases.
ezmlm-list(1), ezmlm-make(1), ezmlm-manage(1), ezmlm-sub(1), ezmlm-unsub(1), qmail-multi(1) qmail-queue(1) ezmlm-queue(1), qmail-qmqpc(1) ezmlm(5), ezmlmrc(5), ezmlmsubrc(5),